Saturday, September 28, 2019

Construction of a line parallel to a given line

एक दी हुई रेखा के समांतर रेखा खींचना
हमें एक रेखा l और एक बिन्दु N जो दी गयी रेखा के बाहर स्थित है , दिया गया है। बिन्दु N से होते हुए रूलर और परकार की मदद से रेखा l के समांतर एक रेखा m की रचना करनी है। रचना के चरण इस प्रकार हैं :

चरण 1 - दी गयी रेखा l खींचिए और रेखा के बाहर एक बिन्दु N लीजिए।

चरण 2 – रेखा l पर एक बिन्दु A अंकित कीजिए और बिन्दु A से बिन्दु N को मिलाइए।

चरण 3 – बिन्दु A को केन्द्र मानकर और एक सुविधाजनक त्रिज्या लेकर एक चाप बनाइए। यह चाप रेखा l को B पर और AN को C पर काटता है।

चरण 4 – बिन्दु N को केन्द्र और चरण 3 की त्रिज्या लेकर एक चाप बनाइए जो NA को बिन्दु D पर काटता है।

चरण 5 – परकार को BC लंबाई के बराबर खोलिए।

चरण 6 – D को केन्द्र मानकर परकार का खुलाव चरण 5 के बराबर रखते हुए एक चाप खींचिए जो चरण 4 के चाप को बिन्दु E पर काटता है।

चरण 7 – EN को मिलाकर रेखा m खींचिए जो दी गयी रेखा l के समांतर है।

नीचे एपलेट में उपर दिए चरण दिखाए गए हैं। एपलेट में ∠BAN = ∠ENA है , जो अंत: एकांतर कोण हैं , अत: रेखा m || रेखा l है। बिन्दु K को माउस की मदद से खींचकर रेखा l की अलग अलग परिस्थितियों में समांतर रेखा की रचना देखी जा सकती है।

Construction of a line parallel to a given line
We are given a line l and a point N not on the given line. We need to construct a line m with the help of ruler and compass through N parallel to the given line l. Following are the steps of construction:

Step 1 – Draw a line l and take a point N, not on the given line.

Step 2 – Take a point A on the given line l and join A with N.

Step 3 – Taking A as a center and a suitable radius draw an arc. This arc cuts the line l at B and AN at C.

Step 4 – Taking N as a center and with the radius of step 3, draw an arc which cuts NA at point D.

Step 5 – Open the compass equal in length to BC.

Step 6 – Taking D as a center and opening of the compass as in step 5 draw an arc which intersects the arc of step 4 at point E.

Step 7 – Join points E and N to make line m which is parallel to the line l.

The steps of constructions can be seen in the applet below. We can see that ∠BAN = ∠ENA, these are internal alternate angles. So line m || line l. Drag point K to see the construction of the parallel line in different positions of given line l.

No comments:

Post a Comment